SMV stepping motor valve
A line of electronic two-way metering valves is presented. High precision linear stepping motors drive the valve spindle. The resolution of the stepping motor driven needles is 0.000125"/step. Low differential pressure valves, may be operated continuously (100% duty cycle). Valves stay in position as when de-energized.
Advantages over solenoid operated valves include cool operations, i.e. there are no control operating problems due to coils heating up, extremely fine resolution, very low differential pressures and high operating pressures. Valves are controllable by 12Vdc CMOS compatible logic level and analog 0 to 2.5 Vdc signals.
OperationWhen the "DIRECTION" is set LOW (GND) the valve spindle travels downward (closes), when it is set HIGH, the valve spindle moves upward (opens). The "SPEED" voltage on pin 4 determines how quickly the valve opens or closes. The signal amplitude for the "SPEED" control signal must remain within the limits of 0 to +2.5 VDC. It may be necessary to override "DIRECTION" and "SPEED" signals with the preset (2.75 Vdc) speed control signal.
This can be accomplished with valve CLOSE and PURGE control signals (open collector NPN compatible). In order to CLOSE the valve, pin 3 on the 9-pin "D"-connector has to be connected to GND (pin 2). A GREEN light on the top of the valve will indicate a CLOSEd valve condition. In order to PURGE the valve, pin 7 on the 9-pin "D"-connector has to be connected to GND (pin 2). A RED light on the top of the valve will indicate a fully OPEN valve condition.
During normal operation the valve remains in the last position as it is deenergized. After powering up, the valve will be automatically closed within the first 10 seconds and after that resumes control operation.
Operating power and valve control signals are supplied via the “D”-connector.
SPECIFICATIONS |
ALUMINUM MODELS aluminum housings and valve blocks, Viton® o-rings, PFA closing pins |
STAINLESS STEEL/PTFE MODELS 316 stainless steel valve blocks, PTFE lined aluminum housing blocks, Viton® o-rings, and PFA closing pins |
MAXIMUM FLOW RATES 1000 sL/min (air), 28 L/min (water) |
CONNECTIONS 3/8 inch, 1/2 inch compression and 3/4 inch FNPT |
ELECTRICAL CONNECTIONS 9-pin "D"-connector, located at the side of the valve |
POWER INPUT +12 Vdc @ 800 mA; protected by a 1600 mA resettable fuse |
DIRECTIONAL CONTROL SIGNAL 12Vdc CMOS compatible logic level signal (10K input impedance); (logic high >= 10 Vdc, low <= 1.5 Vdc) |
SPEED CONTROL SIGNAL analog 0 to 5 Vdc (100K input impedance); ON/OFF override: logic low level to pins 7 and 3 (10K input impendence) |
RESPONSE TIME 100 ms time constant |
DIFFERENTIAL PRESSURES 10 to 15 psid (700 to 1000 mbars) |
MAXIMUM OPERATING PRESSURE 500 psig (35 bars) |
MAXIMUM DIFFERENTIAL PRESSURE 40 psig (2.7 bars) |
|
VITON® is a registered trademark of DuPont Dow Elastomers |
PSV / PSV-D literature PSV proportional solenoid valve and PSV-D driver module catalog page(s)
SMV Series Stepping Motor Valves Operating Manual SMV Operating Manual - TD0305M, Rev. G, Nov-2022
Digital and Analog Flow Meters Catalog Full line Digital and Analog Flow Meters, Controllers, Valves and Accessories Catalog
Valve Catalog Valve Catalog - precision barstock valves, PTFE precision needle valves, PSV proportional solenoid valves, stepping motor valves
Rotameter Catalog Full line Rotameter and Valves Catalog